Lectrosonics SRc5P Dual Channel Slot Mount ENG Receiver B-1

The SRc5P and SRc consists of two separate receivers built into a single, ultra compact housing with adapters for video camera receiver slots and for stand-alone use. Digital Hybrid Wireless® technology provides superb, compandor-free audio quality and compatibility with other wireless systems. The RF performance is extremely stable over a very wide temperature range, making the receiver perfectly suited to the rough environmental conditions found in field production.

Fits camera “slots,” Lectrosonics Duopack adapter and Octopack multicoupler, and operates stand-alone with various adapters
Tunes over a 75 MHz range* (3 blocks)
Dual receiver design for two channels with phase switched diversity or single channel with ratio diversity operation
Digital Hybrid Wireless® with compatibility modes for use with other transmitters
Tracking front-end filters for high performance in tough RF environments
LCD with RF spectrum scanning
SmartSquelchTM DSP-controlled, noise based filtering and squelch
DSP-based pilot tone for squelch control
IR sync port for quick transmitter setup (LMb, LT, HHa, HMa, & SSM)

DSP compatibility modes allow the receiver to be used with a variety of Lectrosonics systems, other brands of wireless systems and with Lectrosonics IFB transmitters.SmartTune operation for quick and confident frequency selection

Operating Frequencies	B1: 537.600 to 614.375 MHz
Frequency Selection Steps	Selectable; 100 or 25 kHz
Type of Receiver	Dual conversion, superheterodyne
IF Frequency	Ch.1: 248.450 MHz and 350.000 kHz Ch.2: 243.950 MHz and 250.000 kHz
Frequency Stability	±0.001 %
Front End Bandwidth	20 MHz @ -3 dB
Sensitivity	20 dB SINAD: 1.0 uV (-107 dBm), A-weighted 60 dB Quieting: 2.2 uV (-100 dBm), A-weighted
Squelch Quieting	Greater than 100 dB typical
AM Rejection	Greater than 60 dB, 4 uV to 1 V
Modulation Acceptance	85 kHz
Image and Spurious Rejection	85 dB
Third Order Intercept	0 dBm
Diversity Method	SmartDiversity phased antenna combining or Ratio Diversity using both receivers for a single audio channel
FM Detector	Digital Pulse Counting Detector operating at 250 and 350 kHz
RF Spectrum Analyzer	Coarse and fine scanning modes for RF spectrum site survey
Antenna Inputs	50 Ohms SMA female connectors
Audio Output Connectors	Interchangeable D-connector adapters for camera-slot interfaces Dual TA3 male (mini XLR) balanced output adapter Balanced output adapter with fixed cables Front-panel TA5M with two balanced outputs (5P version)
Audio Output Level	Adjustable -50 to +5 dBu in 1 dB steps; unbalanced output is 6 dB lower
Audio Channel Crosstalk	-80 dB or better
Front Panel Controls and Indicators	Sealed panel with membrane switches LCD monitors pilot tone; antenna phase, receiver battery level; transmitter battery status; audio level, RF level
Audio Test Tone	1 kHz, -50 dBu to +5 dBu output (bal); 1% THD
Transmitter Battery Type Selection	9 V alkaline, 9 V lithium, AA alkaline, AA lithium, NiMH
Phase Invert	Audio output phase normal or inverted
Compatibility Modes	HYB native Digital Hybrid mode M.3 non-Lectrosonics (call factory) 200 Lectrosonics 200 Series 100 Lectrosonics 100 Series HYB/TB Digital Hybrid w/ Talkback M.7 non-Lectrosonics (call factory) M.6 non-Lectrosonics (call factory) IFB Lectrosonics IFB
SmartNR (Noise Reduction)	Off, Norman, Full modes (available in Digital Hybrid mode only)


Frequency Response	32 Hz to 20 kHz (+/- 1 dB)
THD	0.15% (system) typical in Digital Hybrid mode
Input Dynamic Range	125 dB (with full Tx limiting)
Rear Panel Controls	Audio output connectors External DC input
Powering and Current Consumption	Min. 7 V to max. 18 VDC; 2.2 W 125 mA at 18 VDC 180 mA at 12 VDC 295 mA at 7 VDC
Runtime with SRBATTSLED Adapter	7.2 V, 2200 mAh "L" style battery will typically provide about 11 hours of operation
Transmitter Battery	Level Tracking: LCD display with battery icon or timer readout
Operating Temperature	-4 to 122°F (-20 to +50°C)
Dimensions (W x H x D)	2.68 x 0.72 x 3.52" (68 x 18 x 89 mm)
Weight	7 oz (195 g)